Central Filter Systems XFC-S Series Effective: 04/05 Part #: 882.00091.00 Bulletin #: XX4-615.3 1

2. Safety Instructions  These safety instructions apply to all persons who may use the equipment, and should be used by all persons assigned activiti

2.1.2. Assembly To prevent injury and/or damage to equipment, observe the following safety rules: • Compare the connected loads with those of the mai

2.1.3. Operation To prevent injury and/or damage to equipment, observe the following safety rules: • Appoint an equipment foreman to be responsible f

2.2. For the Operating Safety of the Equipment • Never change settings if the consequences are not precisely known. • Use only original manufacture

3. Transport, Assembly and Storage    This chapter is intended for all operating personnel of the equipment. Personnel using these instructions mus

4. Assembly Instructions    These installation instructions are intended for persons with skills in electrical and mechanical areas due to their tr

4.1. Installation Use the following procedure to install the safety filter: Place the safety filter in the conveying system directly before the vacu

4.2. Installing the Filter Shroud (XFC 225 and XFC 1000 only) The cloth filter shroud is mounted to a ring on the underside of the filter chamber s

4.3. Electrical Connection  Be safety conscious! High or low voltage can cause serious or fatal injury. Installation must be performed by qualified

4.3.2. XFC-A Run electrical cable from the blowback valve to the conveying controller. Check control schematics for proper terminal connection points

ACS Group 800 Wood Dale Drive Wood Dale, IL 60191 Telephone: (630) 595-1060 Fax: (630) 595-8924 www.acscorporate.com Technical Service: Service depar

4.3.3. XFC-S, XFC 225, XFC 1000 The XFC 225 and XFC 1000 safety filters feature compressed air blowback. The XFC-S safety filter is available with eit

4.5. Implosion Blowback Connection The clearing valve (implosion blowback valve) is located on the outlet of the vacuum filter. Connect the clearing

5. Functional Description  This functional description is intended for all operating personnel of the equipment. General knowledge of conveying sys

6. Operation  Before operating the central safety filters, make sure all mechanical installations are complete. Make sure all electrical and compre

6.2. Adjusting the Number of Air Pulses The number of air pulses during blowback can be adjusted as necessary to effectively clean the filter element

7. Maintenance    This chapter is intended for persons with skills in electrical and mechanical areas obtained from their training, experience and

7.1 Maintenance Intervals Daily: Check that warning labels on the equipment are clear and readable. Check the waste level in the collection bin, and

7.2 Servicing the Filter  Stop conveying before servicing the filter. Turn off the conveying system at the main power switch. Depressurize all sect

7.5. Cleaning/Replacing the Filter Cartridge 7.5.1. XFC-A Use the following procedure to clean or replace the filter cartridge: 1. Open the clamp o

Please note that our address and phone information has changed. Please reference this page for updated contact information. These manuals are obsolet

7.5.2. XFC-K Use the following procedure to clean or replace the filter cartridge: 1. Open the toggle fasteners on the lid of the filter. 2. Remo

7.5.3. XFC-S Use the following procedure to clean or replace the filter cartridge: 1. Unlatch the four (4) clamps that hold the collection bin to

7.5.4. XFC 225 and XFC 1000 Use the following procedure to clean or replace the filter cartridge: 1. Unlatch the clamp that secures the cover ass

7.6. Replacing the Gaskets (XFC-K/XFC-A only) The XFC-K and XFC-A safety filters include several gaskets that should be checked periodically and rep

7.6.2. Replacing the Dump Valve Gasket (XFC-K/XFC-A only) The dump valve is located on the bottom of the filter chamber, just above the collection b

7.7. Replacing/Cleaning the Filter Cartridge of the Collection Bin Vent (XFC-K only) XFC-K filter chambers feature an additional filter cartridge ne

7.8. Dismantling and Disposal  Only skilled personnel qualified for this work may dismantle the individual product modules. Parts that are under

8. Technical Data  These instructions apply to all persons within who may operate the equipment. These operating instructions are to be used by all p

Dimension Sheets XFC-K Wall Mounting Plate 37

XFC-A Wall Mounting Plate 38

Shipping Information Unpacking and Inspection You should inspect your equipment for possible shipping damage. Thoroughly check the equipment for any d

142438401313.50265928 WALL MOUNTWall mount FLOOR MOUNTFloor mount SPC PUMP MOUNTSPC Pump Mount 11.736.2516.000.5013.50 XPC Filter Mounting Plate 39

XFC 225 and XFC 1000 40

9. Spare Parts Lists  This spare parts list is intended to be used only by trained personnel. Other persons are not permitted to modify or repair t

9.1 Parts Breakdown, XFC-K 42

9.2 Parts List, XFC-K Pos. Part # Name 1 CT28622 Valve housing 5 CT28624 Collecting bin 6 CT23093 Outlet flap with magnet 7

9.3. Parts Breakdown, XFC-A 44

9.4. Parts List, XFC-A Pos. Part # Name 1 CT93551 Compressed air cylinder 3 CT96372 Solenoid valve 12 CT98177 PVC fabric ho

9.5. Parts Breakdown, XFC-S 46

9.6. Parts List, XFC-S Implosion blowback and compressed air blowback assemblies shown together. Actual configuration depends on blowback method. I

9.7. XFC 225 Qty. Part No. Description 1 A0547008 Filter, cart, wire mesh, polyester media 1 A0539933 Gasket, fltr, element,

Warranty We warrant all of our equipment to be free from defects in workmanship and material when used under recommended conditions. The manufacturer’

10. Troubleshooting Problem Possible Cause Solution High-vacuum alarm Filter element dirty. Clean or replace filter Dump delay time set to zero, o

11. Technical Assistance 11.1. Parts Department Call toll-free 7am–5pm CST [800] 423-3183 or call [630] 595-1060, Fax [630] 475-7005 The ACS Customer

Table of Contents 1. General Instructions ... 7 1.1. War

10. Troubleshooting... 48 11. Technical Assistance .

1. General Instructions       These instructions apply to all persons who may operate the equipment. These operating instructions are to be rea

1.2. Explanations and Information Various terms are used in these operating instructions to ensure clarity. Therefore, please note that the terms use